TuneWorks

Plan a race fuel load, reserve, start weight, and projected minimum-weight margin. Calculates from measured inputs without authentication and does not read or save account data. Assumes the entered per-lap consumption applies to race, formation, and allowance laps. Finish weight retains only the selected reserve. Confirm your series weighing rules and validate consumption with real data.

Check speed, RPM, and shift drop from tire size, final drive, and gear ratio. Calculates from measured inputs without authentication and does not read or save account data. Use measured tire diameter when possible. Tire growth and converter/clutch slip can move real-world numbers.

Turn cold, hot, and target hot pressures into the next cold pressure to try. Calculates from measured inputs without authentication and does not read or save account data. This gives a next-test pressure, not a universal ideal. Recheck after the next run.

Calculate cross weight, left/right balance, and front/rear split from four scale pads. Calculates from measured inputs without authentication and does not read or save account data. Measure the car in the same state you drive it: driver, fuel, ballast, and tire pressures matter.

Convert spring rate and motion ratio into wheel rate for setup comparisons. Calculates from measured inputs without authentication and does not read or save account data. Wheel rate compares spring changes. It does not account for bars, bump stops, tires, or aero load.

Estimate injector size from horsepower, fuel type, injector count, and duty cycle. Calculates from measured inputs without authentication and does not read or save account data. This is a sizing estimate. Confirm with your tuner and fuel pressure data.

Convert AFR and lambda across gasoline, E85, methanol, and race fuel scales. Calculates from measured inputs without authentication and does not read or save account data. Use this as a conversion reference. Tune targets depend on fuel, engine, load, and calibration strategy.

Estimate front brake bias from piston area, rotor size, and pad friction. Calculates from measured inputs without authentication and does not read or save account data. This estimates mechanical bias. Tire grip, weight transfer, ABS, and balance bars still matter.

Compare tire diameter, circumference, ride height, and speedometer change. Calculates from measured inputs without authentication and does not read or save account data. Actual mounted diameter changes by tire model and pressure. Use manufacturer specs when available.

Check camber and total toe against broad autocross and track baseline ranges. Calculates from measured inputs without authentication and does not read or save account data. This is a baseline checker, not a vehicle-specific prescription. Tire wear and driver feedback decide the next step.

Compare two laps or sector sets and see the best theoretical lap. Calculates from measured inputs without authentication and does not read or save account data. Use sectors from timing, video, or data logs. Compare similar conditions before blaming setup.

Calculates an ethanol blend for a fresh tank, existing fuel, correction, or ratio without authentication or account-data access. Percentages are 0–100 and all volumes use the selected unit. Source ethanol contents are measured values. Fresh mode requires finalVolume; existing mode requires finalVolume, currentVolume, and currentEthanol; correction mode requires tankCapacity, currentVolume, and currentEthanol; ratio mode requires no volumes.

Provides understeer/oversteer setup guidance without authentication or access to TuneWorks account data.

Interprets inside, middle, and outside tire temperature readings without authentication or access to TuneWorks account data.

Provides a bounded shock/damper adjustment recommendation without authentication or access to TuneWorks account data.

Search the public TuneWorks Autocross Site Finder by coordinates and minimum paved-area dimensions. This may take several minutes because it queries live map and imagery providers.

Describes TuneWorks free public capabilities and connected garage capabilities for vehicles, setups, sessions, maintenance, shop lists, Share Build, and log history.

無需輸入參數。

Adds a vehicle to the connected user’s TuneWorks garage so setup, session, modification, maintenance, and optimization context can be attached. Deletes are not supported.

Edits an existing vehicle in the connected user’s TuneWorks garage. Deletes are not supported.

List bounded structured modifications for an accessible TuneWorks vehicle.

Read one structured modification from an accessible TuneWorks vehicle.

Create a structured modification on an editable TuneWorks vehicle.

Update a structured modification on an editable TuneWorks vehicle.

Mark a modification canceled so it remains in vehicle history. Requires explicit confirmation.

Permanently delete a vehicle modification and its files. Requires explicit confirmation.

Returns the connected garage, its activation stage, missing baseline data, and the next available actions toward vehicle optimization.

無需輸入參數。

Lists vehicles saved in the connected user’s TuneWorks app garage and reports the next activation action when the garage is empty.

Returns one saved TuneWorks vehicle with modifications, setups, sessions, maintenance, lists, log metadata, optimization readiness, and next actions.

List bounded metadata for logs attached to one connected TuneWorks vehicle. Raw log samples are not returned.

Read bounded metadata, channel schema summary, and saved focus window for one accessible TuneWorks log. Raw log samples are not returned.

List recent AI Log Tuner conversations owned by the connected TuneWorks user. Returns conversation metadata without message contents.

Read the ordered messages and saved analysis summaries for one AI Log Tuner conversation owned by the connected TuneWorks user.

List recent AI Race Engineer conversations owned by the connected TuneWorks user. May be filtered to one vehicle.

Read one AI Race Engineer conversation and its ordered messages. Internal execution debug traces are not returned.

Archive a connected user vehicle using TuneWorks soft-delete behavior. Requires explicit user confirmation and never hard-deletes data.

Lists chassis setups and setup history saved in the connected TuneWorks account.

Saves a new TuneWorks setup for a vehicle. Deletes are not supported.

Edits an existing TuneWorks setup revision. Deletes are not supported.

Archive all active revisions of a connected user setup. Requires explicit user confirmation and never hard-deletes data.

Lists driving sessions, events, track days, autocross runs, and session notes saved in TuneWorks.

Saves a new TuneWorks driving session. Deletes are not supported.

Edits an existing TuneWorks driving session. Deletes are not supported.

Create an additive copy of an accessible TuneWorks driving session.

Archive a connected user driving session. Requires explicit user confirmation and never hard-deletes data.

Lists service reminders, maintenance history, due work, and completed maintenance saved in TuneWorks.

Creates a TuneWorks maintenance reminder or service item. Deletes are not supported.

Edits a TuneWorks maintenance reminder or service item. Deletes are not supported.

Archive a connected user maintenance item. Requires explicit user confirmation and never hard-deletes data.

Lists reusable shop lists, event prep lists, task lists, and parts lists saved in TuneWorks.

Read one connected user shop list with its categories and items.

Lists individual items and completion status in one connected user shop list, with optional filtering for open or completed items.

Creates a TuneWorks shop list, task list, or parts list, optionally including categories and items.

Edits shop-list metadata or replaces the full categories and items collection.

Atomically add one category to an existing editable shop list without replacing its existing categories or items.

Atomically add one item to an existing editable shop list without replacing existing items. If its category does not exist yet, TuneWorks creates it.

Create an editable copy of a connected user shop list with all item checks reset.

Reset every item in a connected user shop list to unchecked/open.

Atomically check or uncheck one shop-list item, change its quantity, or do both.

Archive a connected user shop list so it no longer appears in active lists. Requires explicit user confirmation.

Delete a connected user shop list from active use by safely archiving it. Requires explicit user confirmation and does not hard-delete history.

Lists existing TuneWorks vehicles, setups, and sessions available for Share Build.

Summarizes selected Share Build vehicle, setups, sessions, recipients, and message without sending email.

Read the connected user’s preferences, unit choices, and custom vehicle makes.

無需輸入參數。

Update selected preferences for the connected TuneWorks user.

Update unit-category choices for the connected TuneWorks user.

Add a custom vehicle make to connected user settings.

Rename or rescope a custom vehicle make.

Permanently delete a custom vehicle make after explicit confirmation.

List saved chart-channel sets.

無需輸入參數。

Save a named set of chart channels.

Update the last-used time for a saved chart-channel set.

Permanently delete a saved chart-channel set after explicit confirmation.

List favorite charts for an accessible vehicle.

Save a favorite chart for an accessible vehicle and source log.

Permanently delete a favorite chart after explicit confirmation.

Read the saved map-channel configuration for an accessible vehicle.

Create or replace the connected user’s complete map-channel configuration.

Record completed maintenance in vehicle history and advance its tracker.

List ECU-file metadata, optionally scoped to an accessible TuneWorks vehicle. Supplying vehicleId enables vehicle-specific recovery guidance. Binary contents are never returned.

Inspect one authorized ECU file and optionally a decoded table. Binary contents are never returned.

Start or retry processing for an existing ECU definition file. This does not upload, create, or read a file, and processing may consume compute and analysis resources.

Retry an eligible failed, already stored ECU file. MCP does not upload binaries.

Permanently delete an authorized ECU file after explicit confirmation.

Emails selected TuneWorks vehicle, setup, and session details to up to three recipients. Explicit user confirmation is required.

List teams available to the connected user, or read one team’s settings.

Create a new team for the connected user.

Replace a team’s name.

Replace a team member’s role.

Remove a member from a team after explicit confirmation.

Revoke a pending team invitation after explicit confirmation.

Remove the connected user from a team after explicit confirmation.

Delete a team after explicit confirmation.

Create and email a team invitation only after explicit user confirmation.

List custom tracks accessible to the connected user.

Read one accessible custom track.

Create a custom track for the connected user or an editable team.

Replace the editable fields and ownership scope of a custom track.

Permanently delete a custom track after explicit confirmation.

List attachment metadata for an authorized object. Binary contents are unavailable through MCP.

Delete an object attachment from blob storage after explicit confirmation.